Based on the current weather at the time of writing, the following plot and Nav Log are created.Ĭontrast this with the following example where the climbs were all moved up one leg.Ġ6C 420019N0880841W/A025 421157N0880632W/A031 C81 ENW210012/A045 C89 KMKE Overfly Sylvania Airport C89, then climb to reach an altitude of 4500 feet at or before this point. Fly to the chain of lakes at Lindenhurst that is 12 miles on radial 210 of the ENW VOR at Kenosha. Fly over Campbell Airport C81 and then climb to reach an altitude of 3100 feet. Fly to the Lake Zurich reporting point at 42☁1’57″N, 88☀6’32″W and then climb to reach an altitude of 2500 feet at or before this waypoint. Fly to the intersection of Barrington Rd and Irving Park Rd at 42☀0’19″N, 88☈’41″W reaching an altitude of 1600 feet. Note, for arrivals with more than one route converging, only waypoints after the merge can precede the arrival waypoints along the branches cannot be used with arrival procedures.Įxamples: BDF BDF7, BRADFORD SEVEN arrival at KORD starting at waypoint BDF. The NavLog will have all of the waypoints of the arrival procedure.
Skyvector to fltplan go code#
First enter a waypoint listed on the procedure, then enter the 3 to 5-digit code for the procedure immediately followed by the number of the procedure.
Skyvector will fill in UECKR.Īrrival procedures should only be filled in after the Destination Airport is filled in. The NavLog will have all waypoints of the departure procedure.Įxamples: JORJO5, JORJO FIVE from KPWK. will fill in the fixes based on the departure. Enter the 5-character name immediately followed by the number of the procedure. The numbers are hundreds of the Mach numberĮxample /M095 changes the airspeed to Mach 0.95ĭeparture procedures should only be filled in after the Departure Airport is filled in. F060 changes the flight level to FL060 (6000 feet).Įxample: /N0120 changes the airspeed to 120 knots. Altitude modifiers are the altitude that will be reached, if possible, after the waypoint is reached.Įxample: /A045 to change the altitude of the waypoint to 4500 feet MSL.Įxample: /F160 changes the flight level to FL160. When altitudes are modified, SkyVector will compute TOC and TOD based on aircraft performance in the NavLog. Important: the cruise altitude and speed entered at the top of the flight plan should be reached at or before for the first waypoint. To modify both speed and altitude include both with no spaces between, e.g. To add a modifier, add a forward slash / after the waypoint. Modifiers are added to waypoints to change either the altitude or speed at that waypoint. SkyVector will fill in the start and end points of that route.Įxample: 06C to KJVL, enter V24. Victor routes should only be entered in between two waypoints, or between a departure and destination. Convert decimal minutes into seconds before entering.
GG (optional) is the 2-digit seconds of longitudeĮnter the GPS coordinate all as one large block. PAPPI intersectionįF (optional) is the 2-digit minutes of longitude VFR Waypoint, Intersection, RNAV WaypointĮxamples: VPFTS, Fort Sheridan. Alternatively DPA000005, Dupage 000 radial, 5 nm. Fractions of a mile and fractions of a radial are not permitted.Įxamples: OBK090010, Northbrook VOR, 090 radial, 10 nm. Place the cursor in the white box to begin typing.ĬCC is the 3 digit distance in nautical miles.Įnter the ICAO code immediately followed by the 3-digit radial and immediately followed by the 3-digit distance in nautical miles.
0 kommentar(er)
